From: Stephen M. Elwood <selwood**At_Symbol_Here**PRINCETON.EDU>
Subject: Re: [DCHAS-L] Fume Hood Ducting
Date: Mon, 16 Oct 2017 10:12:10 +0000
Reply-To: ACS Division of Chemical Health and Safety <DCHAS-L**At_Symbol_Here**PRINCETON.EDU>
Message-ID: E04A30DE-5F03-41CC-87D7-C85993EE34DC**At_Symbol_Here**exchange.Princeton.EDU
In-Reply-To <88B8FAA1-40A1-4AAE-A7E2-A50D2F286478**At_Symbol_Here**mit.edu>


Not adding anything new here, except to concur with the point made by Jim on use and maintenance of oil Ômist' separators and filters on vacuum pump  exhaust.


We have been dealing with this very same issue in our engineering buildings and believe we have a consensus on the source - poorly maintained vacuum pumps.

In some cases the filters had not been installed or had been removed.  In most other cases the filters had not been properly maintained.

There is also the issue of responsibility for periodic maintenance of pump exhaust filtration; researchers feel it is a building maintenance responsibility and the facility groups the opposite.

Stephen Elwood

Associate Director


On Oct 12, 2017, at 5:33 PM, Jim Doughty <jdoughty**At_Symbol_Here**MIT.EDU> wrote:

As a further note I would ask if your researchers are using oil most filters, and if so are they being maintained? The most common we have,BOC Edwards, need to be periodically drained (there is drain plug in the side). If the oil reaches a certain level the oil most will blow by the filter and not filter at all. 

Jim

Sent from my iPhone

On Oct 12, 2017, at 5:29 PM, Jim Doughty <jdoughty**At_Symbol_Here**MIT.EDU> wrote:

Hello,

We experienced this in our Chemistry Department; however, we believed it to be from vacuum pumps and the likely culprit were those pumps that had hard connections to their exhaust duct. A better setup is to insert the vacuum pump hose into the duct and let room air flush the duct out continuously. Hard connections are frequently made unintentionally when some tries to figure out how to keep the hose from falling out of the duct and then duct tapes over the whole thing or similar. This was particularly noteable in our labs with a high glove box density.

Hope that helps.

Jim Doughty
MIT

Sent from my iPhone

On Oct 12, 2017, at 4:46 PM, Elizabeth Brubaker <ebrubaker**At_Symbol_Here**MURRAYSTATE.EDU> wrote:

Has anyone experienced accumulation of oil (perhaps mineral oil from a heated oil bath?) in fume hood duct work? Is this reasonable or even possible? Could a sufficient amount remain in the system for it to condense out in the ducts when the exhaust fans were turned off for an extended period?

--
Beth Brubaker
Laboratory/Safety/Waste Coordinator
Murray State University Department of Chemistry
2226 Jesse D. Jones Hall
Murray, KY  42071-3300
(270) 809-6390
--- For more information about the DCHAS-L e-mail list, contact the Divisional secretary at secretary**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas
--- For more information about the DCHAS-L e-mail list, contact the Divisional secretary at secretary**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas
--- For more information about the DCHAS-L e-mail list, contact the Divisional secretary at secretary**At_Symbol_Here**dchas.org Follow us on Twitter **At_Symbol_Here**acsdchas

Previous post   |  Top of Page   |   Next post



The content of this page reflects the personal opinion(s) of the author(s) only, not the American Chemical Society, ILPI, Safety Emporium, or any other party. Use of any information on this page is at the reader's own risk. Unauthorized reproduction of these materials is prohibited. Send questions/comments about the archive to secretary@dchas.org.
The maintenance and hosting of the DCHAS-L archive is provided through the generous support of Safety Emporium.