From: Jean & Ken Smith <smith.j.k**At_Symbol_Here**SBCGLOBAL.NET>
Subject: Re: [DCHAS-L] Oxygen Sensor
Date: August 30, 2012 1:27:47 AM EDT
Reply-To: DCHAS-L <DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU>
Message-ID: <CACO1vYPKbkLAZoWcZSci0E=hK-=rOSdwhe_tAVO5eUCj7KiUWg**At_Symbol_Here**mail.gmail.com>


Hi Barb,

No need to be embarrassed.  You are not the first and certainly the last to make the mistake, especially for those who have not had a reason to use the SCBA.  I ran into many persons who made the same error.  Now you can spread the word to others.

Ken Smith

 

-----Original Message-----
From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU] On Behalf Of Barbara Wiehe
Sent: Wednesday, August 29, 2012 1:04 PM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: Re: [DCHAS-L] Oxygen Sensor

 

I am absolutely flame red with embarrassment!!  I even looked it up so I would not make that mistake.  I pull the red flag in the first week of our semester..

On Wed, Aug 29, 2012 at 2:50 PM, Jean & Ken Smith <smith.j.k**At_Symbol_Here**sbcglobal.net> wrote:

Hi Barb,

First – the term is SCBA not SCUBA.  The SCUBA is for underwater use.  When working for Cal/OSHA I encountered a person trying to don the SCBA as an SCUBA.  Fortunately, he was inside a filtered operations room.  This was in a huge gaseous phenol release so he didn’t get hurt.  He obviously was not trained in the proper use of the SCBA and the company was hit with a serious citation for it.

 

The SCBA is mandatory to enter an oxygen deficient room unless a handheld gas monitor is used to verify that actual oxygen concentration is not hazardous.  Pay attention to the local state OHSA regulations on oxygen deficient atmospheres so you don’t get into trouble.  They are actually good common sense regulations to prevent deaths. 

 

The oxygen room monitor needs to be installed according to regulations with the readout on the outside of the room or building.  The sensor must be recalibrated often due to the deterioration of the sensor.  It will need to be re-spanned at least each 6 months to assure a good response to low levels of oxygen.

 

At the lab where I was the EHS officer, we had a large liquid nitrogen leak in a room full of dewars containing biological specimens.  The alarm went off and we double checked the atmosphere by slightly opening the door and putting the handheld monitor inside.  The readings were very low % and would have been deadly if entered.   Especially dangerous is a liquid nitrogen spill/leak due to its density which will pool on the floor and easily rise to the nose level with asphyxiating consequences.

 

Training for the SCBA is regulated by OSHA and needs to be followed closely.  If no person has accreditation for training on SCBAs, then a professional trainer will be necessary.

 

End result:  Be very careful when dealing with asphyxiating gasses for they can and will bite you.

 

Ken Smith (former CIH, now retired)

 

-----Original Message-----
From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU] On Behalf Of Barbara Wiehe
Sent: Wednesday, August 29, 2012 10:23 AM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: Re: [DCHAS-L] Oxygen Sensor

 

Thank you for your responses.

Neal, fair enough put the red flags away...I was thinking scuba but it isn't going to fly with anyone here to go to that extent.

I appreciate getting feedback from your perspectives rather than push back from others.


Barb

On Wed, Aug 29, 2012 at 12:45 PM, Neal Langerman <neal**At_Symbol_Here**chemical-safety.com> wrote:

Several thing – first and foremost The only protection for an oxygen deficient environment is a supplied air source.  Thus, a question regarding “respirator fit” raises a flag.

 

Having supervised the installation of many oxygen sensors in locations where a deficiency can occur, here are some thoughts

 

The sensor should be located IN the area to monitor and installed according to the manufacturer’s instructions.  Pay particular attention to the vertical height instruction.

 

The sensor is low voltage, but the installation still must comply with the NEC.

 

The alarm should be in the monitored area and repeated just outside the affected zone and also at a central monitoring location.

 

Provide regular maintenance as required by the manufacturer.  While using a two gas calibration to set the span works, some sensors are calibrated with ambient oxygen, set to 20.8%.  It is very useful to periodically test the sensor with a low oxygen source. 

 

Most electrochemical oxygen sensors require replacement every two years.  In the very dry climate of southern California, we find that they need more frequent replacement.

 

False alarms from an oxygen sensor should be very infrequent.  If false alarms occur with an annoying frequency, work with the manufacturer to fix it – false alarms lead to the “chicken little” problem.

 

Your responders to an alarm, be it maintenance or other, should bring a working 4-gas portable with them to provide a back-up to the installed system.

 

Finally, installed sensors are really great, but they require active PM and some understanding of their limitations.

 

Neal

------------------------------------------------------------------------------------

The information contained in this message is privileged and confidential and protected from disclosure. If the reader of this message is not the intended recipient, or an employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any dissemination, distribution or copying of this communication is strictly prohibited. If you have received this communication in error, please notify us immediately by replying to the message and deleting it from your computer.

 

ACSafety has a new address:

NEAL LANGERMAN, Ph.D.

ADVANCED CHEMICAL SAFETY, Inc.

PO Box 152329

SAN DIEGO CA 92195

011(619) 990-4908 (phone, 24/7)

www.chemical-safety.com

 

We no longer support FAX.

 

 

 

From: DCHAS-L Discussion List [mailto:dchas-l**At_Symbol_Here**MED.CORNELL.EDU] On Behalf Of bjwiehe**At_Symbol_Here**OWU.EDU
Sent: Wednesday, August 29, 2012 7:01 AM
To: DCHAS-L**At_Symbol_Here**MED.CORNELL.EDU
Subject: [DCHAS-L] Oxygen Sensor

 

We are installing an Oxygen Sensor in a room using Liquid Nitrogen.  Question, why do you mount it in the room where loss of Oxygen would be present?  What type of training should the technician have overseeing the monitor?(ie respirator fit)

 

 

Barb Wiehe

 




--

Barbara Wiehe

Ohio Wesleyan University
Environmental Health and Safety / Greenhouse Manager
740-368-3502




--

Barbara Wiehe

Ohio Wesleyan University
Environmental Health and Safety / Greenhouse Manager
740-368-3502

Previous post   |  Top of Page   |   Next post



The content of this page reflects the personal opinion(s) of the author(s) only, not the American Chemical Society, ILPI, Safety Emporium, or any other party. Use of any information on this page is at the reader's own risk. Unauthorized reproduction of these materials is prohibited. Send questions/comments about the archive to secretary@dchas.org.
The maintenance and hosting of the DCHAS-L archive is provided through the generous support of Safety Emporium.